0102030405
China Factory Suppliers of Hydz D17H4 Piezoelectric Sounder – Low Power, High Reliability, and Cost-Effective Solution
Electrical Characteristics
| # | Parameter | Value |
|---|---|---|
| Part No：HYR-1704P | ||
| 1 | Resonance Frequency (KHz) | 4.0 |
| 2 | Max Input Voltage (Vp-p) | 30 |
| 3 | Capacitance at 120Hz (nF) | 14,000±30% at 100Hz |
| 4 | Sound Output at 10cm (dB) | ≥80 at 4.0KHz Square Wave 5Vp-p |
| 5 | Current Consumption (mA) | ≤5 at 4.0KHz Square Wave 5Vp-p |
| 6 | Operating Temperature (℃) | -20～+70 |
| 7 | Storage Temperature (℃) | -30～+80 |
| 8 | Weight (g) | 0.7 |
| 9 | Housing Material | Black PBT |
Dimensions and Material (unit: mm)
📐
Tolerance：±0.5mm Except Specified
Notice (Handling)
- Do not apply DC bias to the piezoelectric buzzer; otherwise insulation resistance may become low and affect the performance.
- Do not supply any voltage higher than applicable to the piezoelectric buzzer.
- Do not use the piezoelectric buzzer outdoors. It is designed for indoor use. If the piezoelectric buzzer has to be used outdoors, provide it with waterproofing measures; it will not operate normally if subjected to moisture.
- Do not wash the piezoelectric buzzer with solvent or allow gas to enter it while washing; any solvent that enters it may stay inside a long time and damage it.
- A piezoelectric ceramic material of approximately 100µm thick is used in the sound generator of the buzzer. Do not press the sound generator through the sound release hole otherwise the ceramic material may break. Do not stack the piezoelectric buzzers without packing.
- Do not apply any mechanical force to the piezoelectric buzzer; otherwise the case may deform and result in improper operation.
- Do not place any shielding material or the like just in front of the sound release hole of the buzzer; otherwise the sound pressure may vary and result in unstable buzzer operation. Make sure that the buzzer is not affected by a standing wave or the like.
- Be sure to solder the buzzer terminal at 350°C max. (80W max.) (soldering iron trip) within 5 seconds using a solder containing silver.
- Avoid using the piezoelectric buzzer for a long time where any corrosive gas (H2S, etc.) exists; otherwise the parts or sound generator may be corroded and result in improper operation.
- Be careful not to drop the piezoelectric buzzer.
Frequently Asked Questions (FAQ)
Q
What is the resonance frequency of the HYR-1704P piezoelectric buzzer?
The HYR-1704P operates at a resonance frequency of 4.0 KHz, making it suitable for alarm, notification, and indicator applications that require a clear, audible tone.
Q
Can the HYR-1704P piezoelectric buzzer be used outdoors?
The HYR-1704P is designed for indoor use only. If outdoor use is required, appropriate waterproofing measures must be applied, as moisture exposure may prevent normal operation.
Q
What is the maximum input voltage for the HYR-1704P buzzer?
The maximum input voltage for the HYR-1704P is 30 Vp-p. Supplying a voltage higher than this rated value may damage the buzzer and affect its performance.
Q
What soldering requirements should be followed when installing the HYR-1704P?
Soldering should be performed at a maximum temperature of 350°C (80W max.) using a soldering iron, and must be completed within 5 seconds. A solder containing silver is recommended for best results.
Q
What is the operating temperature range of the HYR-1704P?
The HYR-1704P piezoelectric buzzer has an operating temperature range of -20°C to +70°C, and a storage temperature range of -30°C to +80°C, ensuring reliable performance across a wide range of environments.
Q
What housing material is used in the HYR-1704P, and what is its weight?
The HYR-1704P features a housing made of Black PBT (Polybutylene Terephthalate), a durable and heat-resistant thermoplastic. The total weight of the buzzer is approximately 0.7 grams, making it lightweight and easy to integrate into compact electronic designs.